The count of manufactures depend on the software you have purchased. When all of the manufactures have been downloaded please exit safely near the left hand top of the screen. However it is necessary to install the drivers on Windows 98 CD driver disks included in the kit with x Please click on the source folder browse icon to locate your desktop then find the x folder you created.
Then on the Launch update screen you should see all of the data and car manufactures in the top left hand side left click on select all. Once you have done that please click on the target folder browser icon to locate your USB CF data card reader.
Locate the removable disc were the cf card is. Please check the hardware info. Note: Time to time you may receive a decompression error when trying to update. This is normal this fault is normally down to insufficient space on the cf memory card. And the update will fail.
You will have to delete some of the old updates in the card to resolve this problem. To delete the unwanted manufactures in the cf card please left click Icon in the bottom left of the screen.
After this is done you can now repeat the update 33 again with the new date software yet again please wait…. Note: When this has happened please follow the cf card removal guide. Other wise the date in the cf card will be lost. Procedure for pulling out the X CF card reader:. On the desktop of windows, open the window of my computer click the right mouse button on the removable disc to pop up a menu. Scroll down to eject in the menu. Then pull out the cf card reader.
Once done remove card from the card reader and place back into the side of the launch x then try on a vehicle. Download the new program by following here. If the above does not work for you then try the compressed zip version. If some manufacturers have initially failed, do not worry as the program will go back over them once it gets to the bottom of the list. Please do not use the PC or surf the web whilst the software is being updated, it will corrupt and slow down the process. If your memory card is low on free space it will not update, follow these instructions on clearing all data off the device by using your PC to format the drive.
Updating your Launch scan tool has never been easier! Using our new One-Click update software, you can sit back and let your computer update your Launch diagnostics saving you time and money!
You have now downloaded and installed the program. You should see a new icon on your PC desktop. Double click on this icon to open the program and update your equipment. Now that you have installed the update tool and formatted your memory card you can start the update process following the below steps; If you have not inserted the USB card reader into your PC with a memory card you will see the below screen. Otherwise it will automatically detect and go straight to the login screen.
To update using this program you must have an active internet connection on your PC, as on the next stage the program will scan the server to see what is available in accordance with your subscription period. This should not take long, please be patient whilst it is loading.
Once the program has populated an update list it will show you what is available for updates. It is important not to surf the web or use your PC whilst the program updates as you will slow and corrupt the update process.
If it starts failing and skipping a manufacturer or two leave it updating as it will automatically go back to the ones which have failed and reinstall those updates. If it starts failing all the manufacturers then you do not have enough space on your memory card because you have not formatted it or your internet connection has gone down.
Otherwise the program should continue updating the manufacturers one by one. If you are doing a complete update this may take minutes depending upon your internet connection and PC speed. If the program is only updating a few manufacturers for you then it will take much less time. Once updates are completed, press exit at the bottom right of the page to come out of the update tool.
Insert memory card back into Launch scan tool and power it up. On the start up procedure, it will say detecting noise do not press anything while this is starting up. When the 4 square dots appear in the middle of the screen you must press and hold for seconds with the stylus until it lights up, then, release the stylus, it will go to the bottom left corner and you press and hold again for seconds, lights up and release, do this for all corners and you have calibrated the screen.
Free download: X Easy Update Tool. Left click folder then automatically will go to the desk top again asking you to rename the new folder left click into the grey colour box rename the folder x Please load internet to your home page In the internet address bar at the top please go to www. The username and password will be provided by your dealer.
Please note: 1. Connect your phone to your computer. We go to the phone and see a new folder cnlaunch. We go into it.
And so with all brands. When copying, it prompts you to replace some files, or rather two, agree. Turning off the phone from the computer. In no case do not run the program. Go to the phone — in settings-manager application-EasyDiag.
In memory of clean data and cache my 6th andoroid, you might have a different location. It is only after you have cleaned the data and shut down the program, you can go into it. Again, scroll through and ASO, machinery steels without arrows down, ie, they are activated.
Enter again your login and password. See the information — should be written at the bottom of your scanner is activated serial number. And the last manipulation — are back on the menu, find the Settings button, then — Settings for the App and hold your finger on — Show only models to strip turns red. Now we will improve our program. We throw it in the Download folder. In general, we do the same as written in paragraph 3a. Exit and disconnect the phone from the computer.
Now you have the version PRO. It has more functions than just EasyDiag. We go into it and immediately exit. The program creates the necessary files and folders. DAT and insert it into each model. While you can activate all of these models. How to activate it is written in paragraphs of the old method, will not be worse. The only condition — that would work EasyDiag program, there you put the old version of machines Arhive1. But, I repeat, we do not need this program, we need PRO version. Actually, this can put a point.
So say the test this method. But they say it can not work.
0コメント